KAKUTE F7 HDV

Overview
HolyBro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.

Notice: The port to the DJI air unit on KAKUTE F7 HDV and KAKUTE F7 HDV AIO have been optimized, the output voltage has increased to 9V/2A.

Features

• Supports Betaflight.
• High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
• Dedicated bootloader button for easy firmware flashing.
• Low-profile design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV monitors voltage directly from the power supply.
• Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 9V output up to 2A to DJI FPV VTx.
• Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

• MCU: STM32F745 32-bit processor
• IMU:MPU6000
• Barometer: BMP280
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 6 hardware UARTS (UART1,2,3,4,6,7)
• All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
• TF card for Blackbox logging
• Dimensions: 35x35mm
• Mounting Holes: Standard 30.5mm square to center of holes
• Weight: 8g

Tekko32 F4 4in1 ESC(45A)

Features:

• F4 MCU, double the speed of F051
• 32bit ESC with BLHELI32 firmware
• Maximum PWM output upto 128K (default 96K)
• Supports 3-6S lipo input
• PWM input, TLM supported
• Voltage output (VBAT)
• No output BEC
• Supports oneshot / Multishot / Dshot / PWM
• Supports damped light
• Extra capacitor needed for high current or 6s usage
• Dimensions: 44x37x6mm
• Mounting holes 30.5×30.5mm(M4)
• Weight: 13.3g

PIN MAP:

Please update your BLHeliSuite32 into the latest version.

Tekko32 F4 Metal 4in1 65A ESC (65A)

4 MCU / BLHELI32 / Metal case mosfet / PWM output 128K / 4~6S
The New BLHELI32 ESC adapted the F4 MCU, which will provide a smoother control and faster response speed.

SPEC:

● F4(M4 Core) 108Mhz MCU with BLHELI32 firmware
● Maximum PWM output upto128K (default 96K)
● The 4in1 has onboard analog current sensor, and TLM function (then no current reading over TLM)
● Uses metal case mosfet for better heat dissipation
● No output BEC
● Supports Lipo 4-6S
● Extra capacitor needed for 6s (1000uf 35v for 6s usage.)
● Dimensions:43 x 44mm
● Mounting holes:30.5×30.5mm(M4)
● Weight: 15.8g

Notice:

The air flow is very important if you want to run this 4in1 in high current.
The input cable (from Lipo to 4in1) should be at least 12AWG and well soldered.

PIN MAP

Package includes:

KAKUTE F7 HDV STACK *1
Electrolytic capacito: 1000uF 35v *1
8pin to 8pin 1mm pitch 65mm cable *1
8pin to 8pin 1mm pitch 25mm cable *1
JST GHR 8pin to JST GHR 6pin 80mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST GHR 8pin to JST GHR 6pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)

Manual:

Some Tips:

BLHeli_32 ESC Firmware Overview
GitHub